硅晶圆通槽激光电化学复合加工试验研究
CSTR:
作者:
作者单位:

(江苏大学机械工程学院,江苏镇江 212013)

作者简介:

毛东晨(1999-),男,江苏省无锡市人,硕士研究生,主要研究方向为激光电化学复合加工硅晶圆贯通微结构;朱浩(1987-),男,河南省周口市人,博士,副教授,主要研究方向为微细加工/特种制造技术。

通讯作者:

中图分类号:

TN305. 7

基金项目:


Experimental Study on Laser-Electrochemical Hybrid Machining of Through-Slots in Silicon Wafers
Author:
Affiliation:

(School of Mechanical Engineering,Jiangsu University,Zhenjiang 212013,CHN)

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    单晶硅作为半导体器件的核心基础材料,具有高硬度、高脆性和低断裂韧度等特性,在微纳加工领域面临显著挑战。激光加工技术广泛用于单晶硅微结构加工,但其固有的热效应易导致材料热损伤。针对这一问题,文章提出一种基于激光电化学复合的硅晶圆通槽加工新方法,用于硅晶圆通槽的高质量加工。该方法基于单晶硅导电性随温度升高的物理特性,通过激光的光 -热耦合效应激发材料的导电活性,实现激光刻蚀与电化学溶解的协同作用机制。研究揭示了激光诱导电化学加工的物理化学机理,并据此设计了相应的试验装置与工艺方案。对比实验数据表明,激光电化学复合加工在表面质量方面优于传统激光干切方法。通过参数优化实验发现,当施加电压达到 40 V时,加工表面粗糙度可显著降低至 310 nm,相较于基础工艺有较大提升,展现出优异的加工质量调控能力。

    Abstract:

    Monocrystalline silicon,a basic material for semiconductor devices,is characterized by high hardness,high brittleness,and low fracture toughness,which pose significant challenges to micro-nano processing. Laser machining is widely used to fabricate monocrystalline silicon microstructures,despite the accompanying notable thermal damage. To address this issue,a novel method is proposed for the through-groove machining of silicon wafers based on laser-electrochemical hybrid processing. This method leverages the photothermal coupling effect of lasers and increased conductivity of monocrystalline silicon with temperature,to achieve a combination of laser etching and electrochemical dissolution,thereby effectively improving the machining quality. The mechanism of laser-induced electrochemical machining is elucidated,and a corresponding experimental scheme is designed. Comparative experimental results demonstrated that laser-electrochemical hybrid processing surpasses traditional laser dry cutting methods in terms of surface quality. Further investigations into the effect of the applied voltage on machining surface quality revealed that at a voltage of 40 V,the surface roughness was significantly reduced to 310 nm,achieving optimal machining outcomes.

    参考文献
    相似文献
    引证文献
引用本文

毛东晨,张文颉,赵康程,朱浩.硅晶圆通槽激光电化学复合加工试验研究[J].半导体光电,2025,46(2):293-298. MAO Dongchen, ZHANG Wenjie, ZHAO Kangcheng, ZHU Hao. Experimental Study on Laser-Electrochemical Hybrid Machining of Through-Slots in Silicon Wafers[J].,2025,46(2):293-298.

复制
分享
相关视频

文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2025-03-11
  • 最后修改日期:
  • 录用日期:
  • 在线发布日期: 2025-06-26
  • 出版日期:
文章二维码