磨粒辅助激光电化学复合加工硅通孔技术研究
CSTR:
作者:
作者单位:

(江苏大学机械工程学院,江苏镇江 212013)

作者简介:

张文颉(1999-),男,江苏省镇江市人,硕士研究生,主要研究方向为半导体材料的激光电化学复合微加工技术研究。朱浩(1987-),男,河南省周口市人,博士,副教授,博士生导师,主要研究方向为半导体材料的微细加工技术、特种制造技术及复合加工技术研究。

通讯作者:

中图分类号:

TN249

基金项目:


Study on Abrasive-Assisted Laser-Electrochemical Hybrid Machining of Through-Silicon Vias
Author:
Affiliation:

(School of Mechanical Engineering,Jiangsu University,Zhenjiang 212013,CHN)

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    针对单晶硅通孔结构的高质量加工需求,提出一种磨粒辅助激光电化学复合加工方法。该方法在激光电化学复合加工的同时,利用激光诱导的空化效应驱动磨粒高速运动并冲蚀通孔内壁,去除表面的熔渣和氧化层。对比分析了磨粒辅助对加工质量的提升效果,并探究了激光功率和外加电压对加工结果的影响。结果表明,磨粒辅助加工显著提高了激光电化学复合加工的质量;当激光功率为 26 W时,硅通孔内壁氧含量降低至 3. 27%,面粗糙度减小至 454 nm,通孔锥度减小至 3. 26°,达到最佳加工效果;当电压为 30 V时,硅通孔的形貌最佳,孔壁光滑且锥度最小。

    Abstract:

    To meet the demand for high-quality through-silicon via(TSV)machining,in this study, we propose an abrasive-assisted laser-electrochemical hybrid machining method. In this combined method, which leverages laser electrochemical processing and laser-induced cavitation effects,abrasive particles cause high-speed erosion of inner walls,effectively removing surface slag and oxide layers. The effects of abrasive assistance on machining quality are evaluated through a comparative analysis,and the influence of laser power and applied voltage on the processing results is systematically examined. The results show that abrasive-assisted machining substantially improves the quality of laser-electrochemical hybrid processing. At the optimal laser power of 26 W,the TSV inner walls exhibit low oxygen contents(3. 27%),low surface roughness(454 nm),and small taper angles(3. 26°),which confirm the superior machining performance of the proposed method. At an applied voltage of 30 V,the TSVs exhibit an optimal morphology with smooth sidewalls and a minimal taper angle.

    参考文献
    相似文献
    引证文献
引用本文

张文颉,毛东晨,朱浩.磨粒辅助激光电化学复合加工硅通孔技术研究[J].半导体光电,2025,46(3):484-492. ZHANG Wenjie, MAO Dongchen, ZHU Hao. Study on Abrasive-Assisted Laser-Electrochemical Hybrid Machining of Through-Silicon Vias[J].,2025,46(3):484-492.

复制
分享
相关视频

文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2025-04-08
  • 最后修改日期:
  • 录用日期:
  • 在线发布日期: 2025-07-28
  • 出版日期:
文章二维码