面向激光芯片的铬锆铜微流道热沉 SLM制造与散热性能研究
CSTR:
作者:
作者单位:

(1.五邑大学机械与自动化工程学院,广东江门 529020;2.香港科技大学机械工程系,中国香港 999077)

作者简介:

蔡益勋(1999-),男,湖南省衡阳市人,硕士研究生,主要研究方向为金属增材制造工艺研究;曹明轩(1986-),男,博士,研究生导师,主要研究方向为大功率激光芯片热管理、激光选区熔覆设备的研发。

通讯作者:

中图分类号:

O351

基金项目:

广东省重点领域研发计划资助项目(2020B090922004);粤港澳联合研发基金资助项目(2019WGALH22)


Study on the Fabrication and Heat Sink Performance of Cu-Cr-Zr Micro-Channel Heat Sinking SLM for Laser Chips
Author:
Affiliation:

(1. School of Mechanical and Automation Engineering,Wuyi University,Jiangmen 529020,CHN;2. Department of Mechanical Engineering,The Hong Kong University of Science and Technology,Hong Kong 999077,CHN)

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用选择性激光熔化(Selective Laser Melting,SLM)技术制备铬锆铜(Cu-Cr-Zr)微流道热沉(Micro-Channel Heat Sink,MCHS)。对流道可成型最小尺寸进行优化和测试,当MCHS的流道高度和宽度的设计尺寸为 1.7 mm时,实际流道高度和宽度成型尺寸约为1. 078 mm,1. 415 mm,若流道高度设计尺寸小于 1.7 mm,则易发生流道堵塞现象。在热沉表面焊接半导体激光芯片后,测试输出特性,结果显示:激光芯片的阈值电流为 1.02 A;当驱动电流为

    Abstract:

    A micro?channel heat sink (MCHS) made of chromium?zirconium?copper (Cu?Cr?Zr) was fabricated using selective laser melting (SLM) technology. The minimum achievable dimensions of the MCHS flow channels were optimized and tested. When the designed height and width were set to 1.7 mm, the actual formed dimensions measure approximately 1.078 mm in height and 1.415 mm in width. Further experiments have shown that reducing the designed channel height below 1.7 mm significantly increases the likelihood of flow channel blockage. Following the soldering of a semiconductor laser chip onto the heat sink surface, its output characteristics were evaluated. The laser chip exhibited a threshold current of 1.02 A. At a driving current of 5.39 A, the output power reached 4.601 W with a slope efficiency of 0.85 W/A. Additionally, the thermal resistance of the MCHS made of Cu?Cr?Zr has been measured as 7.33 °C/W. A 50 h stability test showed that the output power of the laser chip decreased by 8.54% before stabilizing. The experimental results confirm the feasibility of using SLM technology for MCHS fabrication and its potential for industrial?scale production.

    参考文献
    相似文献
    引证文献
引用本文

蔡益勋,杨光照,钟鑫,潘琳琳,曹明轩,付斌,袁铭辉,李会军.面向激光芯片的铬锆铜微流道热沉 SLM制造与散热性能研究[J].半导体光电,2025,46(4):630-637. CAI Yixun, YANG Guangzhao, ZHONG Xin, PAN Linlin, CAO Mingxuan, FU Bin, YUAN Minghui, LI Huijun. Study on the Fabrication and Heat Sink Performance of Cu-Cr-Zr Micro-Channel Heat Sinking SLM for Laser Chips[J].,2025,46(4):630-637.

复制
分享
相关视频

文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2025-02-24
  • 最后修改日期:
  • 录用日期:
  • 在线发布日期: 2025-08-25
  • 出版日期:
文章二维码