磨粒辅助激光电化学复合加工硅通孔技术研究
DOI:
CSTR:
作者:
作者单位:

江苏大学

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金项目(面上项目,重点项目,重大项目)


Research on Abrasive-Assisted Laser-Electrochemical Hybrid Machining Technology for Through-Silicon Vias
Author:
Affiliation:

Jiangsu University

Fund Project:

The National Natural Science Foundation of China (General Program, Key Program, Major Research Plan)

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    单晶硅作为光电器件的基础材料,其高脆性和低断裂韧性给精密加工带来了显著的挑战。针对单晶硅通孔结构的高质量加工需求,本文提出了一种磨粒辅助激光电化学复合加工方法。该方法在激光电化学复合加工的同时,利用激光诱导的空化效应驱动磨粒高速运动并冲蚀通孔内壁,去除表面的熔渣和氧化层。对比分析了磨粒辅助对加工质量的提升效果,并探究了激光功率和外加电压对加工结果的影响。结果表明,磨粒辅助加工显著提高了激光电化学复合加工的质量;当激光功率为26 W时,硅通孔内壁氧含量降低至3.27%,面粗糙度减小至454 nm,通孔锥度减小至3.26°,达到最佳加工效果;当电压为30 V时,硅通孔的形貌最佳,孔壁光滑且锥度最小。

    Abstract:

    As a fundamental material for optoelectronic devices, single-crystal silicon poses significant challenges in precision machining due to its high brittleness and low fracture toughness. To meet the demand for high-quality through-silicon via (TSV) machining, this paper proposes an abrasive-assisted laser-electrochemical hybrid machining method. This approach combines laser-electrochemical processing with laser-induced cavitation effects to drive abrasive particles for high-speed erosion of via inner walls, effectively removing surface slag and oxide layers. The effects of abrasive assistance on machining quality were evaluated through comparative analysis, and the influence of both laser power and applied voltage on processing outcomes was systematically examined. Results show that abrasive-assisted machining substantially improves the quality of laser-electrochemical hybrid processing. At the optimal laser power of 26 W, the TSV inner walls exhibited reduced oxygen content (3.27%), lower surface roughness (454 nm), and a smaller taper angle (3.26°), demonstrating superior machining performance. When the applied voltage was 30 V, the silicon through-holes achieved optimal morphology with smooth sidewalls and minimal taper angle.

    参考文献
    相似文献
    引证文献
引用本文
分享
相关视频

文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2025-04-08
  • 最后修改日期:2025-05-03
  • 录用日期:2025-05-16
  • 在线发布日期:
  • 出版日期:
文章二维码