双光路结构面三维姿态角测量方法研究
CSTR:
作者:
作者单位:

(北京信息科技大学 1.光电测试技术及仪器教育部重点实验室,北京 100192; 2.光纤传感与系统北京实验室,北京 100016)

作者简介:

崔曦文(2000-),女,硕士研究生,主要从事自准直光路角度测量方面的研究;祝连庆(1963-),男,博士,教授,博士生导师,主要从事光纤传感技术和光学测量等方面的研究。

通讯作者:

中图分类号:

TH741;TN249

基金项目:


Three-Dimensional Angle Measurement Method for Structural Planes Based on Dual Optical Paths
Author:
Affiliation:

(1. Beijing Engineering Research Center of Optoelectronic Information and Instruments,Beijing 100192,CHN; 2. Beijing Laboratory of Optical Fiber Sensing and System,Beijing Information Science & Technology University,Beijing 100016,CHN)

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    文章基于双自准直光路建立了一种结构面三维倾角测量模型,通过分析反射镜空间角度分量变换,推导滚转角的测量理论模型,并结合旋转矩阵构建了自准直仪读数与结构面三维倾角的解算模型,分析了测量系统中元件装调引入的误差。搭建了基于双自准直光路的实验系统,针对反射镜安装角度 θ对测量精度的影响,设计不同 θ值(6°~15°)的性能验证实验,分析了测量系统在不同夹角下的误差分布特性,获得最优 θ区间。实验结果表明,当 θ=10°时,系统表现出最优的综合性能:α,β和 γ角的最大误差分别为 0. 31 ″、0. 18 ″和 0. 23 ″。该测量系统在重复性试验中可实现优于 0. 24 ″的均方根误差,表现出较好的重复性和可行性,为结构面的姿态监测提供了一种可供参考的测量方法。

    Abstract:

    In this study,a three-dimensional inclination measurement model was established for a structural surface based on dual-autocollimation optical paths. A theoretical roll-angle-measurement model was constructed based on the analysis of the spatial angular component transformation of the reflector. The autocollimator reading solution model and the three-dimensional inclination model of the structural surface were constructed by combining a rotational matrix. The error due to component mounting in the measurement system was also evaluated. An experimental system based on dual-autocollimation optical path was constructed,and performance verification experiments were performed with different θ values(6° to 15°)to analyze the effect of the mirror mounting angle on the measurement accuracy and to determine the optimal θ interval. Evidently,the system exhibits optimal performance at θ = 10°,and the maximum errors in the α,β,and γ angles are 0. 31 ″,0. 18 ″,and 0. 23 ″,respectively. Repeatability tests reveal that the measurement system achieves a root-mean-square error accuracy better than 0. 24 ″,which confirms its good repeatability and feasibility. Therefore,the proposed system provides a reference measurement method for attitude monitoring of structural surfaces.

    参考文献
    相似文献
    引证文献
引用本文

崔曦文,李红,邢宇航,任琪,祝连庆.双光路结构面三维姿态角测量方法研究[J].半导体光电,2025,46(5):928-935. CUI Xiwen, LI Hong, XING Yuhang, REN Qi, ZHU Lianqing. Three-Dimensional Angle Measurement Method for Structural Planes Based on Dual Optical Paths[J].,2025,46(5):928-935.

复制
分享
相关视频

文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2025-06-28
  • 最后修改日期:
  • 录用日期:
  • 在线发布日期: 2025-10-31
  • 出版日期:
文章二维码