液体辅助飞秒激光加工织构质量试验研究
CSTR:
作者:
作者单位:

(西安工业大学机电工程学院,西安 710021)

作者简介:

严博平(2000-),男,硕士研究生,研究方向为飞秒激光加工表面微织构技术;肖强(1976-),男,博士,教授,研究方向为先进制造技术。

通讯作者:

中图分类号:

TN249

基金项目:


Experimental Study on the Quality of Micro-Textures Fabricated by a Liquid-Assisted Femtosecond Laser
Author:
Affiliation:

(School of Mechatronic Engineering,Xi’an Technological University,Xi’an 710021,CHN)

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    钛合金因摩擦系数大、耐磨性差而限制其在航空航天领域的应用,表面加工微织构可有效改善其摩擦学性能。为提高微织构的加工质量,采用液体辅助飞秒激光加工方法,通过改变激光功率、扫描速度和扫描次数,研究织构尺寸与形貌的变化规律。结果表明:随着激光功率增加,织构的深度和宽度显著增大;随着扫描速度提高,织构的深度和宽度减小;随着扫描次数增加,织构深度增大,但扫描次数超过 2次后宽度保持不变。当激光功率为 2W、扫描速度为 5 mm/s、扫描次数为 1时,可获得最佳的表面微织构形貌。

    Abstract:

    The large friction coefficient and poor wear resistance of titanium alloys limit their application in the aerospace field. Surface micro-textures processed on titanium alloys can improve their tribological properties. To enhance the machining quality of surface micro-textures,this study investigated the quality of micro-textures fabricated using liquid-assisted femtosecond laser processing. Variations in the dimensions and morphology of the textures were studied by adjusting the laser power,scanning speed,and number of scans. The results indicated that the depth and width of the textures significantly increased as the laser power increased,and decreased as the scanning speed increased. However,the depth of the textures increased with the number of scans,while the width remained unchanged when the number of scans exceeded two. The optimal surface micro-texture morphology was achieved at a laser power of 2 W,a scanning speed of 5 mm/s,and a single scan.

    参考文献
    相似文献
    引证文献
引用本文

严博平,肖强.液体辅助飞秒激光加工织构质量试验研究[J].半导体光电,2026,47(3):490-495. YAN Boping, XIAO Qiang. Experimental Study on the Quality of Micro-Textures Fabricated by a Liquid-Assisted Femtosecond Laser[J].,2026,47(3):490-495.

复制
分享
相关视频

文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2026-01-30
  • 最后修改日期:
  • 录用日期:
  • 在线发布日期: 2026-06-25
  • 出版日期:
文章二维码