Si粉和过硫酸铵对湿法刻蚀制备隔离腔的影响
CSTR:
作者:
作者单位:

(1.中国电子科技集团第二十六研究所,重庆 400060;2.南京大学电子科学与工程学院,南京 210046)

作者简介:

郭耀祖(1991-),男,博士,主要从事 MEMS声表滤波器件和 COMS光电器件的设计和工艺等方面的研究工作。

通讯作者:

中图分类号:

TN305. 7

基金项目:


Effect of Silicon Powder and Ammonium Persulfate on Wet Etching for Fabricating Isolation Cavities
Author:
Affiliation:

(1. China Electronics Technology Group Corporation Twenty-Sixth Research Institute,Chongqing 400060,CHN;2. Nanjing University,School of Electronic Science and Engineering,Nanjing 210046,CHN)

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    基于标准 CMOS工艺的微测辐射热计具有传感器与读出电路可一体化集成、工艺简单、成本低以及适合大规模成像阵列制备的优势,其中 post-CMOS是制备该类微测辐射热计热隔离腔的关键工艺。文章系统研究了湿法刻蚀工艺中,Si粉和过硫酸铵含量对制备热隔离腔的影响。研究发现,当使用 5 wt%的四甲基氢氧化铵溶液刻蚀衬底 Si时,在溶液中加入 Si粉能有效抑制金属 Al电极的腐蚀,添加过硫酸铵能够抑制刻蚀过程中产生的氢气泡对刻蚀进程的阻碍作用,从而显著提高衬底 Si的刻蚀表面的平整度。实验结果表明,在四甲基氢氧化铵溶液中,Si粉的最佳浓度为 16×10.3 g/mL,过硫酸铵的最佳浓度为 4×10.3 g/mL。通过该优化后的刻蚀溶液,成功制备了具有良好悬空效果的 CMOS微测辐射热计阵列结构,为后续器件性能的提升提供了重要工艺保障。

    Abstract:

    A microbolometer based on standard CMOS technology enables the monolithic integration of sensors and readout circuitry,offering a simplified fabrication process and low cost;therefore,it is well suited for large-format imaging array fabrication. Post-CMOS processing is a critical step for forming a thermally isolated cavity in this type of microbolometer. In this study,the effects of the additions of silicon powder and ammonium persulfate in a wet-etching process on the fabrication of the thermal isolation cavity were investigated. The results showed that,when the silicon substrate was etched in a 5 wt. % tetramethylammonium hydroxide(TMAH)solution,the addition of silicon powder effectively suppressed the corrosion of the Al electrodes,whereas the incorporation of ammonium persulfate mitigated the hindering effect of hydrogen bubbles generated during etching,thereby significantly improving the planarity of the etched Si surface. The optimal concentrations in the TMAH solution were 16×10-3 g/mL for silicon powder and 4×10-3 g/mL for ammonium persulfate. Ultimately,a CMOS microbolometer array structure with well-suspended membranes was successfully fabricated using the optimized etching solution.

    参考文献
    相似文献
    引证文献
引用本文

郭耀祖,杨正兵,潘祺,杜江,雷凯,周文斌,舒平. Si粉和过硫酸铵对湿法刻蚀制备隔离腔的影响[J].半导体光电,2026,47(3):496-501. GUO Yaozu, YANG Zhengbing, PAN Qi, DU Jiang, LEI Kai, ZHOU Wenbing, SHU Ping. Effect of Silicon Powder and Ammonium Persulfate on Wet Etching for Fabricating Isolation Cavities[J].,2026,47(3):496-501.

复制
分享
相关视频

文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2026-01-26
  • 最后修改日期:
  • 录用日期:
  • 在线发布日期: 2026-06-25
  • 出版日期:
文章二维码