晶硅微通孔激光冲击磨粒与电化学复合加工试验与仿真研究
DOI:
CSTR:
作者:
作者单位:

1.江苏大学;2.机械工程学院

作者简介:

通讯作者:

中图分类号:

基金项目:

江苏省研究生科研创新项目(KYCX25_4174),国家自然科学基金项目(52275431)


Fabrication of Micro-Through-Holes in Silicon Wafers by Laser-Induced Cavitation-Driven Abrasive Erosion and Laser-Enhanced Electrochemical Etching: Experiment and Simulation
Author:
Affiliation:

Jiangsu University

Fund Project:

Jiangsu Province Postgraduate Research Innovation Program(KYCX_4174),The National Natural Science Foundation of China (52275431)

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    针对激光加工单晶硅微孔过程中存在的重熔物堆积、圆度误差大及表面质量差等问题,本文提出一种微磨粒辅助激光电解复合加工方法:利用皮秒激光定域提升晶硅导电性,进而增强局域电化学阳极腐蚀,同时通过激光液下空化驱动微磨粒定域冲蚀,实现多场协同减材。通过对比试验系统分析不同加工工艺的效果,并进一步探讨激光功率对加工质量的影响,同时构建分子动力学模型揭示微磨粒冲蚀的微观机理。结果表明,该复合工艺可显著改善微孔加工质量:孔径由335.2μm增至449.3μm,提升34%,圆度误差由12.2%降至2.7%;在适宜激光功率范围内可获得良好表面形貌,而过高功率会加剧电化学腐蚀及表面缺陷。仿真结果表明,微磨粒冲蚀减材主要由磨粒棱角与顶点的划擦作用主导。该研究为单晶硅高质量微孔加工提供了新的技术路径与理论依据。

    Abstract:

    Aiming at the problems such as remelted material accumulation, large roundness error and poor surface quality in the laser machining of micro-holes on monocrystalline silicon, this paper proposes a hybrid machining method of micro-abrasive assisted laser-electrochemical machining. Picosecond laser is used to locally improve the conductivity of silicon crystal, thereby enhancing localized electrochemical anodic dissolution. Meanwhile, laser-induced cavitation in liquid drives micro-abrasives to perform localized erosion, realizing multi-field synergistic material removal. Comparative experiments are carried out to systematically analyze the effects of different machining processes, and the influence of laser power on machining quality is further investigated. In addition, a molecular dynamics model is established to reveal the microscopic mechanism of micro-abrasive erosion. The results show that the proposed hybrid process can significantly improve the quality of micro-hole machining: the hole diameter increases from 335.2 μm to 449.3 μm, with an improvement of 34%; the roundness error decreases from 12.2% to 2.7%. Favorable surface morphology can be obtained within an appropriate laser power range, while excessive power intensifies electrochemical corrosion and surface defects. Simulation results indicate that material removal by micro-abrasive erosion is dominated by the scratching effect of abrasive edges and vertices. This study provides a novel technical approach and theoretical basis for high-quality micro-hole machining of monocrystalline silicon.

    参考文献
    相似文献
    引证文献
引用本文
分享
相关视频

文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2026-04-06
  • 最后修改日期:2026-05-18
  • 录用日期:2026-05-25
  • 在线发布日期:
  • 出版日期:
文章二维码