基于三次样条插值与 BiLSTM的 FBG形状重构方法
CSTR:
作者:
作者单位:

(1.华北电力大学 电子与通信工程系,河北保定 071003; 2.华北电力大学 河北省电力物联网技术重点实验室,河北保定 071003; 3.华北电力大学 保定市光纤传感与光通信技术重点实验室,河北保定 071003)

作者简介:

尚秋峰(1968—),女,博士,教授,主要研究方向为光电子与光传感;华子昊(1999—),男,硕士研究生,主要研究方向为光电子与光传感。

通讯作者:

中图分类号:

TN911. 6

基金项目:


FBG Shape Reconstruction Method Based on Cubic Spline Interpolation and BiLSTM
Author:
Affiliation:

(1. Dept. of Electronic and Communication Engineering Baoding 071003,CHN;2. Hebei Key Lab. of Power Internet of Things Technol.Baoding 071003,CHN;3. Baoding Key Lab. of Optical Fiber Sensing and Optical Communication Technol., North China Electric Power University,Baoding 071003,CHN)

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    针对光纤布拉格光栅(FBG)形状传感技术中因测点稀疏及 Frenet积分法导致的误差累积严重、重构精度低等问题,文章提出一种基于三次样条插值与双向长短时记忆网络(BiLSTM)的端到端形状重构方法。该方法利用三次样条插值将稀疏的离散应变信号变为稠密的空间应变序列,以满足光纤变形的物理连续性约束;再通过 BiLSTM模型构建光纤沿着轴向的应变传递特征与空间几何约束;实现从应变空间到三维坐标的直接映射。仿真与实验结果表明,该方法摒弃了传统几何重构的逐点推算过程,有效消除了累积误差,仿真结果的相对平均误差分别为 0. 28%和 0. 23%,末端误差分别为 0.271 9 mm和 0.463 9 mm,实验结果的相对平均误差分别为 1. 22%和 1. 03%,末端误差分别为 7.10 mm和 5.47 mm。

    Abstract:

    To address the issues of severe error accumulation and low reconstruction accuracy in fiber Bragg grating shape sensing technology caused by sparse measurement points and the Frenet-Serret integration method,this study proposes an end-to-end shape reconstruction method based on cubic spline interpolation and Bidirectional Long Short-Term Memory(BiLSTM). This method employs cubic spline interpolation to convert sparse discrete strain signals into dense spatial strain sequences,thereby satisfying the physical continuity constraints of optical fiber deformation. Subsequently,a BiLSTM model is used to capture the strain transfer characteristics along the fiber axis and the associated spatial geometric constraints,establishing a direct mapping from strain space to three-dimensional coordinates. Simulation and experimental results show that this method eliminates the point-by-point calculation process used in traditional geometric reconstruction,effectively eliminating cumulative errors. The average relative errors of the simulation results were 0. 28% and 0. 23%,and the endpoint errors were 0.2719 mm and 0.463 9 mm,respectively. The average relative errors of the experimental results were 1. 22% and 1. 03%,and the endpoint errors were 7. 10 mm and 5. 47 mm,respectively.

    参考文献
    相似文献
    引证文献
引用本文

尚秋峰,华子昊,霍景壮,郝登祥.基于三次样条插值与 BiLSTM的 FBG形状重构方法[J].半导体光电,2026,47(5):837-844. SHANG Qiufeng, HUA Zihao, HUO Jinzhuang, HAO Dengxiang. FBG Shape Reconstruction Method Based on Cubic Spline Interpolation and BiLSTM[J].,2026,47(5):837-844.

复制
分享
相关视频

文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2026-02-02
  • 最后修改日期:
  • 录用日期:
  • 在线发布日期: 2026-10-23
  • 出版日期:
文章二维码