基于蓝宝石下转换的紫外能量传感器研制与性能表征
DOI:
CSTR:
作者:
作者单位:

1.重庆光电技术研究所;2.四川压电与声光技术研究所

作者简介:

通讯作者:

中图分类号:

基金项目:


Development and Characterization of Ultraviolet Energy Sensor Based on Sapphire Down-Conversion
Author:
Affiliation:

1.Chongqing Optoelectronics Research Institute;2.Sichuan Institute of Piezoelectric and Acousto-Optic Technology

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    紫外能量传感器是光刻机中监测曝光光源能量的关键零部件。本文基于荧光下转换技术路线,研制了由蓝宝石晶体、光电二极管、信号处理电路、滤光片、机械结构件等组成的紫外能量传感器;采用光学非共轴空间布局,实现多界面光热能量耗散,提高传感器工作稳定性、抗激光损伤能力;提出了基于仿真预测的晶体多自由度互相补偿安装方法,提高响应均匀性;采用近红外增强光电二极管,两级放大、差分输出的电路结构,提高传感器重复性。通过相关双光路对比法,消减光源能量波动对测试结果影响,完成传感器相关性能参数高精度测试表征;测试结果显示其重复性小于0.08%、非线性度达到0.018%、响应频率达到13.9kHz、不稳定性达到0.005%、非均匀性达到0.23%/mm、抗强光损伤能力大于1.5×107个脉冲@(波长193nm、脉宽10ns、能量10mj、重频1000Hz),可应用于相关光刻机曝光能量实时监测。

    Abstract:

    Ultraviolet energy sensors are key components for monitoring the energy intensity of exposure light sources in lithography machines. Based on the fluorescence down-conversion technology route, this paper developed an ultraviolet energy sensor composed of sapphire crystal, photodiode, signal processing circuit, optical filter, and mechanical structural components. An optical non-coaxial spatial layout was adopted to achieve multi-interface photothermal energy dissipation, improving the sensor"s working stability and resistance to laser damage. A crystal multi-degree-of-freedom mutual compensation installation method based on simulation prediction was proposed to enhance response uniformity. A near-infrared enhanced photodiode, a two-stage amplification, and a differential output circuit structure were adopted to improve the sensor"s repeatability. The correlation double-path comparison method was used to reduce the impact of light source energy fluctuations on test results, achieving high-precision testing and characterization of the sensor"s relevant performance parameters. The test results showed that its repeatability was less than 0.08%, nonlinearity reached 0.018%, response frequency reached 13.9kHz, instability reached 0.005%, non-uniformity reached 0.23%/mm, and resistance to intense light damage was greater than 1.5×107 pulses@ (wavelength 193nm, pulse width 10ns, energy 10mj, repetition rate 1000Hz), applied to real-time detection of exposure energy in relevant lithography machines.

    参考文献
    相似文献
    引证文献
引用本文
分享
相关视频

文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2026-07-21
  • 最后修改日期:2026-07-21
  • 录用日期:2026-08-05
  • 在线发布日期:
  • 出版日期:
文章二维码